Lesson 18
Create a Mini-Logo Language
The framework established by classes Pen and Poly allow you to create a miniature version of the Logo language, which controls the position and painted trail on the screen of a triangular object called a turtle”hence the name for this demo: Turtle.
We'll show you a few ways to get started. From there, you should be able to develop a rather sophisticated Logo-like environment.
For this experimentation, we will be writing a customized version of Turtle, which we'll call Logo. We'll be using an editor to modify Turtle and save it as Logo for later loading into Mops.dic.
If you have come to this lesson without turning off your Mac or quitting Mops.dic from the last lesson, then you should remove all of Turtle's code from Mops.dic. The fastest way to do this is to use Mops' FORGET operation. FORGET deletes from the current dictionary in memory all the definitions from a word you specify. In other words, you type FORGET plus the first definition of the Turtle program (Pen) to remove Turtle from memory.
To prove it, type:
forget pen
and then select List Words from the Utilities pull-down menu. After several lines have printed on the screen, press any key (other than the space key) two times. Notice that the word on the top of the dictionary (the one at the upper left of the listing) is Angle, which is the last definition of Sin”the program loaded prior to Turtle.
If, on the other hand, you are starting this lesson fresh, then start up Mops.dic and load Sin. Our Logo program will load atop Sin.
Designing the language
We start by defining in our minds what we want our mini language to do.
First of all, we want a turtle on the screen that will be a triangular object from class Poly.
Next, we want to be able to perform a few maneuvers, such as: centering the turtle on the screen; making it move forward in a given direction according to the number of pixels we specify, while the turtle leaves a trail of its pen on the screen; making it turn to the right or left according to the number of degrees we specify.
Finally, we'll define one shape, a square, which the turtle will draw if we tell it how long its sides should be.
Looking through the methods available in Poly and Pen, we see that if we draw the turtle in one location and then move it to another, the original turtle on the screen will still be there, cluttering up the screen. Therefore, we need to define an additional method, called UNDRAW:, for class Pen that undraws a turtle where we tell it.
Since the UNDRAW: method will be adjusting the PenPattern (from black to white) and redrawing the object, this method will be defined in terms of the DRAW: method. Therefore, we can place the UNDRAW: method anywhere in the class Poly definition after the DRAW: method.
As far as the PenPattern parameters go, you can look in the QuickDraw chapter of Inside Macintosh for guidance. If there is not enough information there to help (and sometimes there is not), you always have the powers of Mops to help you. For example, while you are experimenting with parameters, you can place a special method inside class Pen that fetches the current values of the parameters from an object:
:m INSPECT: \ ( -- HiPat LoPat mode w h x y )
get: PnPatHi get: PenPatLo get: PnMode
get: PnSize get: PnLoc ;m
Send a message like:
inspect: Bic
Then perform a .S operation to view the parameters on the stack. Experiment by placing other values in the parameters via a message that calls the INIT: method. Try to draw some objects to learn the results of the new parameters.
Back to the Logo example and UNDRAW:, the PenPattern values that make a white pen are 0,0 while the values for a black pen are -1,-1. Place one integer of the pair in each variable, PnPatHi and PnPatLo, draw the object with a white pen, and then restore the pen to black.
The UNDRAW: method could look like this:
:m UNDRAW: \ Erases object before moving it and restore black pen
0 0 put: PnPatHi put: PnPatLo draw: self
-1 -1 put: PnPatHi put: PnPatLo ;m
[#Implementing Implementing a Logo-like language]
Here is the listing of Mops definitions added to the end of the modified Turtle listing:
\ Create Logo-like environment
poly turtle \ the name of our Logo object
250 160 center: turtle \ define the center of the screen
10 3 size: turtle \ set turtle's size
: SPOT \ Erases old Logo command onscreen and repositions prompt
8 210 gotoxy ;
: .OK -curs spot 15 spaces spot +curs ;
\ Shortcut definition for later:
: TURN -curs undraw: turtle turn: turtle draw: turtle .ok ;
\ Logo-like commands:
: HOME -curs cls home: turtle up: turtle
draw: turtle .ok ;
: FORWARD \ ( dist -- )
-curs undraw: turtle move: turtle
draw: turtle .ok ;
: LEFT ( deg -- ) turn ;
: RIGHT ( deg -- ) negate turn ;
: SQUARE { len -- }
-curs 4 0 DO len forward 90 right LOOP
.ok ;
The above Mops words should be self explanatory, except perhaps for the two that control the location of the Logo prompt. In Logo, the traditional prompt location is near the lower left corner of the screen. The Mops word .OK always moves the cursor to the prompt location after the object makes its mark on the screen. The 15 SPACES operation is added to overprint the old command for a cleaner look on the screen.
While in your editor, save the modified source as ˜Logo' (perform a Save As... operation from the File menu). Return to the Mops.dic window. Select ˜Echo during load' from the Mops menu. Then load Logo into memory with the Load selection from the File menu or by typing:
// logo
The program source code will appear on the screen, line by line, as it is being compiled into memory. If you used a word not previously defined, the load will stop, and a message will tell you what word you need to define. Some other messages such as ˜object not unique' may appear as well. As long as the load doesn't stop, however, nothing fatal is occurring in memory. When the load is complete, clear the screen with CLS and check your program.
Starting the turtle in the home location, try issuing some Logo commands to make the turtle draw lines, turn, and draw squares of various sizes. You'll notice that after turning the turtle to some degree measures (especially those not multiples of 45), the turtle will not fully erase when you issue the subsequent command. The reason is that when the Toolbox draws the turtle at odd angles, the finishing point of the pen may be a pixel off from the original starting point. Then, when the UNDRAW: method is invoked, it undraws from the finishing point of the last operation, off-register from the original motion by one pixel.
But with Mops, that should present no difficulty. Tackle this problem yourself. Try adding another ivar to the object that remembers the starting point of the turtle, and use that point for the UNDRAW: operation. Then, define new Mops-Logo words that make entry of commands easier (e.g., establish abbreviated Logo commands such as FD for Forward). This is the playground on which to cut your teeth on the words in the Mops glossary and class-object-message relationships.
In the remaining lessons of this tutorial, we'll be exploring some of Mops' predefined classes more closely, with the help of an extension of the Turtle program that adds Macintosh-like features to it, such as scroll bars, mouse input, windows, and menus.
| Lesson 17 | Tutorial | Lesson 19 |
| Documentation | ||
